***** FBV_6x6 ******* This SysEx enables 6 different patches in each bank: 3 tones on lower pedals #1 to#3, 3 tones on upper pedals #6 to #8 with an 'extra' feature:the 'Manual foot setting mode' on bank #0 :-) And Delay & Mods enhanced editing on banks #8 & #9 Bnak #7 is unused The Volume control is on the left pedal(A) and the Wah on the right one (B) (Comp On/Off and Reverb On/Off are not available... except with #0 bank ) ** Banks 1 to6 ** A) Patch Pedals: #1 to 3(lower) and #4 to #6 (upper ): Flex III Presets ordered from: FCB Bank #1: Pedals... #1: 1-A #2: 1-B #3: 1-C #6: 1-D #7: 2-A #8: 2-B FCB bank #2: Pedals... #1: 2-C #2: 2-D #3: 3-A #6: 3-B #7: 3-D #8: 4-A and so on until FCB bank #9 Pedals ...#1: 8-C #2: 8-D #3: 9-A #6: 9-B #7: 9-C #8: 9-D B) Delay Pedals #4: Delay On/Off #5: Tap C) Mod+Wah Pedals #9: Mod On/Off #10/0: Wah On/Off (Each toggle is: 1rst press: On 2nd: Off ) This is necessary because of a FCB limitation: when a patch is called, there is no way for the FCB to know which is the actual setting: On or Off ? So, I made this choice, and the effects needed must be set 'Off' in the Flex III patches themselves if needed. If you need the reverse, just exchange the two values (0 & 127) of CC1 & CC2.. It can be done very fast with the FCB Editor, preset & bank copy features) ** Bank 0 'Extra' feature : Editing mode It's purpose is editing some parameters without using the control panel knobs As the Flex stays on the actual patch selected, this let you modify a tone, and then store it by pressing the lit button on the Flex control panel for more than 5 seconds #1 to #4: A.I.R. settings ( both volume and wah pedals keep active) #1 to 3 act as a toggle: 1rst press On axis 2nd press Off axis #1: Shure SM 57 #2: MD 421 #3: U-67 #4: A.I.R Off #5 to #9: 1rst press: On 2nd: Off ) exp pedal A exp pedal B #5: Gate Threshold Decay time #6: Comp Threshold Gain #7: Mod Tweak Param 2 ( see manual 2.5 ) #8: Delay Tweak Feedback #9: Reverb Level Decay #0: unused.... may be customized with the FCB editor... :-) ** Bank #8 Modulations ** Pressing pedals 1 to 6 set the mod ON and Tweak & 2nd function are available on A & B exp pedals Caution: the operations order is important for a good working Always: 1) select the Type 2) set the Delay Pre/Post ( if necessary ) 3) then tweak either #7 &/or #8 settings #1 to #6: Mod type ( same order as with the mod button ) Pedal A Pedal B #1 to #6: Mod On Tweak Mod 2nd function ( see manual 2.5 ) #7: Mod Vol Mix/Note value Vol/mix Note value (*) #8: Mod settings P3/P4 Param 3 Param 4 (*) #9: Mod Pre/Post Tweak Mod 2nd function ( see manual 2.5 ) (TOGGLE if necessary, set it just AFTER selecting the Mod type) #0: Mod Off ** Bank #9 Delays ** Pressing pedals 1 to6 set the delay ON and Tweak & Feedback are available on A & B exp pedals Caution: the operations order is important for a good working Always: 1) select the Type 2) set the Delay Pre/Post ( if necessary ) 3) then tweak either #7 &/or #8 settings ( including Tap tempo ) #1 to #6: Delay type ( same order as with the delay button ) Pedal A Pedal B #1 to #6: Delay On Tweak Feedback #7:Delay Vol Mix/Note value Vol/mix Note value (*) #8: Delay settings P3/P4 Param 3 Param 4 (*) #9: Delay Pre/Post Tweak Feedback (TOGGLE if necessary, set just AFTER selecting the Delay type) #0: Delay Off Note: The 'Tap Tempo' function is available on either #7 or #8 pedals. Set it AFTER tweak, feedback and Post/pre setting --------------------------------------------------------------- (*) See Flex III manual - Appendix D- Notes 4 & 6 for the Note value, P3 & P4 parameters according to the type of Delay or Mod selected